correctly assembled device demands minimum adjustment.

Caddy_CAN_2004

CRAFTER_CAN_3_2006

EOS_CAN_2006

Golf VI 2008 CAN BUS RU

Golf_plus_CAN_12_2004

GOLF_V_CAN_2005

JETTA_CAN_10_2005

MULTIVAN_2003

PASSAT_CAN_03_2005

POLO_CAN_2002

SCIROCCO_CAN_BUS_2008

SHARAN_2003

Tiguan_CAN_12_2007

TRANSPORTERT52004

VW_GOLF_V_2003

VW_Touareg_2003

Caddy_CAN_2004

CRAFTER_CAN_3_2006

EOS_CAN_2006

Golf VI 2008 CAN BUS RU

Golf_plus_CAN_12_2004

GOLF_V_CAN_2005

JETTA_CAN_10_2005

MULTIVAN_2003

PASSAT_CAN_03_2005

POLO_CAN_2002

SCIROCCO_CAN_BUS_2008

SHARAN_2003

Tiguan_CAN_12_2007

TRANSPORTERT52004

VW_GOLF_V_2003

VW_Touareg_2003

S40_CAN_2005

S60_2003

V50_CAN_2004

V70_CAN_2003

XC70_CAN_2008

XC_70_2003

UN_BLINK&LOCK_v2

UN_BLINK

Auris_CAN_2007

RAV_CAN_2006

Toyota_LANDCRUISER_2003

Yaris_CAN_2006

GRAND_VITARA_2005_CAN_NO_BLIN__

GRAND_VITARA_2005_CAN_ONLY_KE__

Splash_2008

SX4_2006_CAN_NO_BLINKER

SX4_2006_CAN_ONLY_key_less_go__

B9_Tribeca_CAN_2007

Forester_1999

Legacy_2004

Legacy_CAN_2004

Outback_CAN_2004

REXTON_2004

Rexton_CAN_10_2006

SMART03_2007

ALHAMBRA_2003

Leon_06_2005

LEON_CAN_06_2005

TOLEDO_CAN_01_2005

Fabia_CAN_2005

Octavia_2002

Octavia_2004

ROOMSTER_CAN_8_2006

Superb_2002

Superb_2008_CAN_BUS

R_CAN_2005

9_5_CAN_2005

SAAB_9_3_CAN_2002

CLIO_III_(CODE)_2006

CLIO_III_2006

Grand_Modus_CAN_2007

KANGOO 2008

Koleos 2008 CAN BUS T no blinker RU

Laguna3_2008

Megane_II_c2003

MODUS(CODE)_2004

VEL_SATIS_2002

Cayenne_CAN_2003

PORSCHE911_997_07_2004

206_VAN_2003

207_CAN_2006

307_CAN_05_2005

307_CC_2006_NO_PSA

307_CC_2006_NO_PSA_NO_BLINK

307_??_NO_BLINKER_2006

307_??_VAN_2003

308_2007

At the disconnected accumulator plant submit a supply and, selecting resistor R6, install on an output of the accumulator rectifier pressure 6,75 V.Vmesto batteries short-term connect the resistor resistance 10 Ohm capacity of 2 W and measure a current flowing through it. It should not exceed 0,4 � 0,45 A.Izmerjajut pressure 6 In and 3,6 In on an output of stabilizators DA2 and D�� accordingly, as a last resort select resistors R15 and R26 for adjustment of these values.

For check of serviceability of all device include phone - the transmitter and dial phone number on which it will be necessary to phone.

the Board of a security signaling, phone and the accumulator plant are installed in the general strong plastic case. LEDs (5 pieces) are carried out on the front panel of the case (for reserve LEDs can and to be installed). Sealed-contact SF2 can be allocated as in the case and outside in a reserved place. Sensor SF1 allocate on a doorway jamb if the signaling is used indoors, or use the regular door cutout if it is the car. In an autovariant it is desirable to use already available security automobile signaling together with a described signaling device, submitting high level at actuating of an available signaling on lower under the circuit an input of element DD1.4 of a logical node of control closing of button "Call" of phone (thus disconnect sensor SF1 and resistor R16).

Also in the case fix a microphone and the receiver inset derived from the case of phone. In the case bore through two small holes and from within paste to these holes a microphone and the receiver inset. A supply 12 In submit on the unit through a connector allocated on a lateral surface of the case. In an authoring variant to a basic variant of a security signaling (fig. 1), are added two node: the driving sensor (on the circuit it is not shown) and the speech unit (fig. 2).

the Digital output of the sensor of driving is connected to lower under the circuit to an input of element DD1.4 (thus disconnect sensor SF1 and resistor R16). At driving origin in a sensor operative range, on input RS of the trigger there is a high level that leads to start of the multivibrator and the counter of a logical node.

the Speech unit (fig. 2) is intended for a phrase pronunciation "System is activated, please abandon a location" at system activation (a charm present to the sealed-contact at an output from a location). However, it is possible to write down for playback and any other phrase, at will. Speech [4 unit consists of a record chip - displays of speech DD1 and power amplifier DA1. The technique of record of speech 1416� is presented to chip ISD in [4]. At an output from a location, bringing a magnetic charm to sealed-contact SF2, on an output 12 triggers DD3 appear high level. Thus on an output 24 DD1 the speech unit there is a low level that leads to playback of the vocal phrase which have been written down earlier in chip DD1.

the Sensor of driving and the speech unit are installed also in general casing of system.

the printed circuit board Type is resulted on fig. 3 and fig. 4.

Network connection points are shown on fig. 5.

Lacks described above a security signaling are defined in the core by lacks GSM of communication networks.

Toronto escorts | the Sitemap | Links | | The contact information
It is made () with company support - Open Company �the Multihouse Trading�
correctly assembled device demands minimum adjustment.